Replacement straps for Sunlite FlatForm II pedals - Strap size: 340 x 55mm
Keep your handlebar organized and your devices secure with the LW-STD (22.2/25.4/28.6mm) from Minoura. - Alloy clamp for mounting your own device on handlebar or stem - Lightweight and rustproof aluminum construction - Hex wrench required for instillation and removal - Clamp body has (1) M5 Thread hold in center - 22.2 mm-28.6 mm diameter range
The Mag Riser Block 3 from Minoura lifts up your front wheel during a training session to be at a natural level. This block fits both MTB and Road bike tire widths. - Fits under front wheel to level the bike to get natural riding on training - Double grooved design fits your narrow or wide ties - Polyethylene material minimizes weight at 1/2 lb. - 8.6D X 4.7W X 2.75H (inches)
$18.99 $39.99 53% Off
BLE USB Adapter gives Rouvy virtual training software the ability to seamlessly connect to Bluetooth devices and sensors. The adapter contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including Saris smart indoor bicycle trainers and power meters. Most importantly, the BLE USB Adapter is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth adapter for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.
Use these axle nuts to put a city or track bike in a Tacx trainer. The available axle nuts are M10x1 (T1415) and 3/8 Shimano Nexus (T1416). For use with Tacx classic trainers only
The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground
• Plastic riser block allows the position of front wheel at one of two heights
Keeps corrosive sweat from reaching your frame. - Cell phone pouch included.
$29.99 $29.99 On Sale
- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more
The Tacx Sweat Cover protects your bike from corrosion caused by perspiration. It is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting.
The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB
Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only
A sweat cover with a pocket for your smartphone. The sweat cover protects your bike against perspiration and enables the use of a phone while training. The Tacx sweat cover is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting. Suitable for a variety of phone sizes - max. length 138mm, max. width 68mm.
$44.99 - $59.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
The Elite Thru Axle adapter kit makes Elite trainers compatible with bicycles with 10mm to 12mm diameter through bolts on the rear wheel (lengths from 130mm to 148mm boost). Easy to set up to start right away with your training, this Thru Axle adapter is made from quality material to ensure an immediate setup and great protection to the threads of your bicycle frame. This unit does it all!
Connect your PC to CycleOps VirtualTraining.
- Includes Sweatcover for Smartphone (T2931) and Towel (T2940) - 891076
The Tacx trainer tires have been developed specifically for riding indoors on bike trainers. The special rubber minimizes the risk of overheating, slipping, and wear and tear. They are also quieter than regular rear tires on both road and mountain bikes. Tacx trainer tires are not suitable for outside riding.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
• 35.5-inches x 79-inches • Black
Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.
TRAINER THRU AXLE ADAPTER FOR SARIS TRAINERS WHAT'S INCLUDED: - Thru axle - Washers - Endcaps with bolts - The 148x12mm adapters also come with a shorter bolt action slider tube. TRAINER COMPATIBILITY The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. BIKE COMPATIBILITY Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. Both 148x12 Thru Axle Adapters are compatible for both 142 and 148mm bikes. 148x12 Thru Axle Adapter, 1.5 Thread Pitch (9733T) works for: - 148 x 12mm - 142 x 12mm - 1.5 thread pitch
The Trainer Adapter for X-12 Axle allows the use of mountain bikes with axle widths of 142mm or larger on a Tacx trainer. These adapters are only suitable for the Tacx classic trainers.
The Elite Folding Mat increases the comfort of your home cycling setup while protecting the surfaces you train on every day. It's easy to use, store, and transport and can be stored everywhere in your house. Dimensions: 1.8m x .9m
Protects the bicycle from sweat and avoids corrosions or rust. - Prevents an accumulation of sweat on the frame and components that would lead to corrosion or affect the finish - Sits above the top-tube and can be adjusted for different bicycles - Washing-machine friendly
Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our non-slip and water-repellent (aka sweat) Floor Mat is designed to keep you safe and protect your floors while in your cycling cleats indoors. And because your cycling training plan asks for incredibly intense efforts, the Floor Mat can ensure firm contact with the ground and prevent movement during leg-busting intervals. Add a Sweat Guard to your indoor cycling collection and you’ve got a training party! - Non-slip surface keep you safe while in cycling cleats - Protects floors from sweat and bike grime - Water-repellent surface does what it was designed to do – keep sweat off your floor - Compress-ability ensures trainer stays put during intense efforts - Easily rolls up for storage - Cleans easily with soap and water - Absorbs noise and vibration - Enhances overall stability of any indoor trainer setup - 4mm (5/32?) thickness is optimal balance of support and storage
Use these quick releases to put a racing bike with disc brakes or a mountain bike with a quick-release skewer in a Tacx direct drive trainer. Both axles are supplied with an adapter set so you can select the right combination for your bike. These axles are only suitable for the Tacx direct drives.
- Adapter for Tacx Direct Drive trainer - 01 is compatible with 142 x 12mm and 148 x 12mm - 02 is compatible with 135 x 10mm - 03 is compatible with 135 x 12mm (w/5 mm spacer included with every Tacx Direct Drive trainer), 142 x 12mm and 148 x 12mm - 04 The thru axle adapter kit is for bikes with a 12 mm thru axle. The axle adapter is required to couple the rear stay with the thru axle mount on a Tacx NEO or FLUX Smart trainer.
Page 1 of 3 Next page